Complete end to end solution. Our product is designed to produce. The smallest particles in size with range from 001 to. 01 microns (10 to 100 angstroms) or (1 to 10 nanometers). That is the size of silver particles that best absorb light in the indigo range, leaving only its inverse color, transparent to yellow, to be observed. What is in the box. Silver-eMed Colloidal Silver Generator. 2x10cm Ultra Pure Silver Electrodes 9999 (99.99%) 1.5mm diameter (14 Gauge). Flask Erlenmeyer borosilicate glass 250 ml (production vessel). High quality micro USB cable. Portable Digital TDS Meter 0-9990 PPM. Pharmaceutical grade amber glass 100ml. Pharmaceutical grade mist nozal spray 60ml. Graduated pipette dropper 3ml. Build-in step-up power module converting 5V (USB) to 27V (output voltage). Output current limited to 2mA. Automatic mechanic stirring 30 rpm (low noise). 2 position on/off power switch. Blue LED operation indicator. Why you should consider our solution and use it with confidence? Our product is designed to produce high quality colloidal/ionic silver water compromising nothing in the process. Our product is designed to produce the smallest particles in size with range from 001 to. 01 microns (10 to 100 angstroms) or (1 to 10 nano-meters). It has a build-in step-up power module converting 5V to 27 volts and current limiting circuit output to 2mA. Due to the current limiting circuit the silver electrodes lifespan is significantly increased as well as the device extended operation on external battery supply. Using the included digital TDS meter you are able to precisely measure and reach the concentrations you are targeting. Particle size matters (smaller is better). Why we use limited current? Any classical colloidal silver generator will produce ionic silver at the same time it is producing colloids but the key difference to produce smaller particles (ions) is limited output current to be applied. The emitted particle size depends on the intensity of the electrical current while the concentration (strength) depends on the time the current is flowing between the silver electrodes. Higher currents tend to blast off larger particles from the silver therefore we have limited the current to 2mA. Low (limited) current tends to generate smaller particles, and therefore silver ions rich solutions. Bob Becker’s recommendations and our own extensive research in producing high quality colloidal silver water the optimal direct current output appears to be within the range of 25-30 volts. Why stirring the solution is important? In parallel during the process the silver concentration within the distilled water will not be equally redistributed through the volume. It will be significantly higher closer to the electrodes. To limit the concentration of the colloid at any point you need to stir the solution during the process. When preparing your solution give it a time to reach the concentration you are targeting. The batch cycles depends on the colloidal silver strength (ppm) you desire to achieve. Electrodes will darken in color at the end of each cycle. In order to produce high quality and pure colloidal/ionic silver water we strongly recommend you carefully clean the electrodes before each cycle (in 30 minutes to one hour intervals). As you can see from above table the more cycles you perform the stronger the solution will get. However the solution will achieve its saturation somewhere between 20-30ppm. This basically means if you continue the process you may compromise the quality. Take more of the solution with 10-15ppm rather than targeting to achieve higher ppm. Please, refer to the user manual for detailed step by step process walk-trough. The item “COLLOIDAL SILVER generator with STIRRING and CURRENT LIMITING CIRCUIT (full kit)” is in sale since Tuesday, April 30, 2019. This item is in the category “Health & Beauty\Natural & Alternative Remedies\Other Natural Remedies”. The seller is “e-med.instruments” and is located in London. This item can be shipped worldwide.
- Silver Electrodes: 2x10cm Ultra Pure 9999 (99.99) 1.5mm diameter
- Brand: Silver-eMed
- Production Vessel: Flask Erlenmeyer borosilicate glass 250ml
- Stirring Function: Automatic Mechanic Stirring (30 rpm)
- TDS Meter: Portable Digital TDS Meter 0-9990 PPM
- Limited Current: Limited Electrodes Current to 2mA
- Used Voltage: Build in power inverter 5 to 27v
- Country/Region of Manufacture: United Kingdom
- Powered by: micro USB cable (5v)
- Colloidal Silver Particles Size: Silver particles size from 001 to .01 microns
